Plumbing Basics: Before Installing a Bathtub
Plumbing Basics: Before Installing a Bathtub
Blog Article
How do you actually feel when it comes to Installing A Bathtub?
Setting up a bathtub isn't precisely brain surgery, however it does need strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a brand-new one is also a reasonably hard job. If the old bathtub is readily available, the project can relocate easily; if you have to open a wall to get rid of the old bathtub and place the new tub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will require a helper to leave the old bathtub and also set in the brand-new one. Make sure you have actually certified on your own for the task and also are comfortable attempting it. Rather than working with a contractor to take control of a halfway-completed project, it is much better to take into consideration utilizing one prior to you begin. Chances are you may need an expert plumber to make tube connections.
This post will certainly assist you mount a brand-new tub in your washroom if you have currently gotten a brand-new bathtub as well as do not require to change the setup of your previous water supply pipelines.
Your devices and material list should comprise the following:
Getting ready for the Installment
Firstly, the sustaining frame provided with the bath should be fitted (if needed) according to the producer's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to see to it that if the tap comes with a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets unit to prevent pressure on the bath tub.
Fit the flexible tap connectors to the bottom of both taps using 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet via the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you make use of every one of the provided washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath must now prepare to be suited its final setting.
Removing Old Touches
If you require to change old faucets with new ones as a part of your installation, after that the first thing you need to do is disconnect the water. After doing so, activate the taps to drain pipes any kind of water remaining in the system. The process of eliminating the existing taps can be quite bothersome because of the limited access that is often the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the taps. Have a towel prepared for the remaining water that will certainly originate from the pipelines. Once the supply pipelines have actually been gotten rid of, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from turning during this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will need to be cleansed of any type of old sealing substance.
Before proceeding to fit the new taps, compare the pipe links on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Installing the Tub
Utilizing the two wooden boards under its feet, position the bath tub in the required placement. The wood boards are valuable in equally spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 small points.
The next goal is to make sure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and also adjusting the feet on the tub till the level checks out level.
To mount taps, fit the bottom of the furthest flexible faucet port to the appropriate supply pipe by making a compression sign up with; then do the very same for the other tap.
Activate the supply of water and examine all joints and new pipework for leaks and also tighten them if required. Fill the bathtub as well as also inspect the overflow outlet and also the regular outlet for leaks.
Ultimately, repair the bathroom paneling as described in the producer's user's manual. Tiling and also sealing around the bath tub must wait up until the tub has been used at least once as this will certainly settle it into its last setting.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end provides a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require reducing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the faucet in the installing hole in the bath/basin making certain that the washing machines remain in area between the faucet as well as the sink. Safeguard the tap in place with the manufacturer supplied backnut. Once the faucet is safely in position, the supply pipes can be attached to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with normal faucet adapters. The former kind must be attached to the tap finishes first, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bathroom meets the tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the installation can move enough to fracture a stiff seal, creating the water to penetrate the wall surface between the bath as well as the tiling, leading to difficulties with wetness and possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to assimilate your components and installations. They are offered in tubes and cartridges, and also can sealing spaces up to a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of soaked paper or soft rope. Remember to always fill the bathtub with water prior to securing, to permit the motion experienced when the bathtub is in usage. The sealer can crack relatively early if you do not consider this motion prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly offered on the marketplace. It is suggested to fit the tiles utilizing waterproof or waterproof adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I came across that page on Installing A Bathtub when exploring the search engines. If you please set aside a second to distribute this post if you enjoyed it. Thank you for taking the time to read it.
Schedule Your Service Report this page